PGT Kitchen Remodeling Nationwide

PGT Kitchen Remodeling: The Los Angeles Owner’s Guide

PGT kitchen remodeling in Los Angeles typically runs $16,520 to $53,100 for a full renovation, with smaller updates like cabinet replacement and countertop work falling in the $4,720 to $15,340 and $2,360 to $7,670 ranges respectively. We stock and install PGT-compatible cabinetry, hardware, and structural components across the greater Los Angeles area, and most parts matching starts same-day in the shop with installation scheduled within the week. Here’s what most owners discover: a hinge plate has pulled free, a drawer glide snapped mid-cycle, or a corner cabinet frame has begun separating in the dry, warm air that Los Angeles homes cycle through every year from June to October.

Call (470) 298-9650

PGT manufactured kitchen cabinet systems with distinctive frame construction and door profile patterns that look simple at a glance but require exact dimension matching when something fails. We are an independent contractor serving Los Angeles, not affiliated with PGT, which means we carry both OEM-sourced PGT components and quality aftermarket equivalents that often exceed the original spec on hinge duty rating and drawer slide capacity.

Which PGT Models This Applies To

PGT kitchen lines break into three general series families: the builder-grade Belmont series (thermofoil doors, concealed hinges, 5/8-inch box construction), the mid-line Portico series (stained maple and cherry, soft-close hinges standard, plywood drawer boxes), and the upper-line Madison series (frameless full-overlay, dovetail joinery, undermount soft-close glides). The trick in Los Angeles is that many high-end homes built between 2015 and 2025 mix series within the same kitchen, which means a label on one door doesn’t tell you what the island drawers are.

Look inside any drawer for a small white or silver sticker on the left interior wall. If it’s gone, measure the drawer box width between side panels, not the face, and check the hinge mounting pattern on any door. PGT doors use a 35mm cup bore regardless of series, but the door overlay (the amount the door overlaps the frame) runs 1/2 inch on Belmont, 1-1/4 inches on Portico, and full overlay on Madison. An aftermarket hinge with the wrong overlay gives you a door that won’t close flush or sits crooked against its neighbor. For hardware beyond hinges, Blum and Grass brand equivalents fit most PGT cabinetry and typically carry the same or better cycle ratings than factory parts.

Signs Your PGT Kitchen Remodeling Is Failing

• A door hangs low on the hinge side and rubs the frame. The hinge’s internal spring has fatigued, or the cup mounting screws have stripped the particleboard. Replacement hinges solve it; re-tightening into stripped board only lasts weeks.
• Drawer opens with a catch, then drops. A glide ball bearing set has seized or a roller wheel cracked. In Los Angeles, low humidity combined with fine dust accelerates bearing wear, especially in homes near the 405 or 110 corridors.
• A door slab has a hairline crack running from the hinge cutout. Thermofoil over MDF is brittle at the cup bore edge. Once moisture or repeated impact flexes it, the crack spreads. The slab needs replacement, not repair filler.
• Soft-close stops working on one door but not others. The damper piston inside the hinge arm has leaked its fluid. That’s a $4 to $14 part per hinge; replacing the hinge is faster than sourcing just the damper.
• Cabinet box sides are separating at a corner joint. Heat cycling in unconditioned Los Angeles rooms, especially south-facing kitchens, causes factory dowel and glue joints to loosen over 8 to 15 years. This is a frame repair, and it needs to happen before the box pulls away from the wall.

Before

After

Replacement Cost & What’s Included

What you pay depends on scope. A hinge or glide replacement on one or two cabinets runs $230 to $560 in parts and labor for the Los Angeles market. Replacing all door hardware and glides across a ten-cabinet kitchen typically lands between $1,180 and $2,360. A full cabinet replacement carries the $4,720 to $15,340 range, and if the failure is pervasive enough that you’re considering changing the kitchen layout, full-remodel pricing applies at $16,520 to $53,100.

Every quote is a written flat price with the parts itemized: what the component costs, what labor costs, what the disposal fee is if old material is leaving the site. No number changes unless the scope changes, and the scope doesn’t change without a signed change order. The workmanship carries our 365-Day Done Right Promise, which is printed on every invoice, and if a replaced hinge or slide fails within the year we return and make it right at no charge.

DIY or Call Us?

Some of this work is genuinely safe to handle. Adjusting hinge screws to fine-tune a door’s alignment, cleaning a sluggish glide, and replacing a knob or handle are all reasonable DIY tasks. The dividing line is the point where a power tool hits a cabinet box. PGT boxes are particleboard or plywood depending on series, and either one is easy to over-drill or crack if you’re not matching thread pitch and depth against the original hardware. Stripping a hinge cup bore past its tolerance turns a $4 hinge job into a $240 door slab replacement.

High-tension components here are rare but real: some PGT touch-latch systems use a spring-loaded catch under surprising load, and the mechanism should be released with the door braced, not your fingers in the path. If you’re unsure whether you’re working on a spring catch or a damper catch, call (470) 298-9650 and describe what you see. We’ll tell you over the phone whether it’s a safe fix or service call territory, and if we come out, you get a written price before any work starts.

FAQs