A remodeled primary bathroom with a soaking tub and a walk-in shower

Plant Prefab Bathroom Remodeling Nationwide

Free Estimate on SiteCalls Answered by a Live Person, 24/7Background-Checked TechniciansOur technicians have up to 19 years of experience
A remodeled primary bathroom with a soaking tub and walk-in shower
A freestanding soaking tub in a remodeled primary bathroom
A walk-in shower with large-format tile and a built-in niche
A stone counter, tile backsplash and open shelf after a kitchen remodel
A garage converted into a guest room and home office
New architectural shingles with a clean valley
A new casement window over a kitchen sink
A new white vinyl privacy fence with a double gate
Every visit starts with

Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled

We have financing partners for your dream remodel*On approved credit; ask us about your options
Get your free estimate

Plant Prefab Bathroom Remodeling: The Los Angeles Owner’s Guide

A Plant Prefab bathroom remodel in Los Angeles typically runs $10,620-$33,040 installed, depending on whether you’re refreshing a guest bath or reworking a primary suite down to the wall studs. We keep Plant Prefab-compatible fixtures, panels, and trim on hand so most jobs start within a week of the written quote. What usually brings owners to us first is a failure that’s hard to ignore: a shower pan that’s delaminated from its prefab base, a vanity that’s swollen at the bottom edge, or plumbing chases that were never properly sealed against moisture intrusion during the original factory run. You notice it as a soft spot underfoot, a door that no longer closes square, or grout lines that keep cracking no matter how many times you re-caulk them.

Call (470) 298-9650

Which Plant Prefab Models This Applies To

We’ve worked on Plant Prefab’s LivingHome series most often in Los Angeles, but the bathroom assemblies share a common DNA across their catalog: factory-built wet-wall modules, precision-routed panel joints, and fixture rough-ins that are set to within a sixteenth of an inch at the plant. That precision is a good thing until something fails, because a standard off-the-shelf part from a big-box store rarely lines up with the original mounting points. We measure the existing rough-in, pull the factory label if it’s still legible, and match the replacement to the module’s actual dimensions rather than the model name printed in the original spec sheet. For owners who want the OEM part, we can source it through Plant Prefab’s parts channel, but our experience in the field is that a quality aftermarket equivalent from Kohler, Toto, or Delta often installs faster and carries a better residential warranty for Los Angeles water conditions. The compatibility gotcha to know: Plant Prefab bathroom modules from the 2017-2021 production window used a non-standard 54-inch vanity width in several floor plans, which means a 48-inch or 60-inch drop-in replacement leaves a gap or requires filler panels. We measure before we quote, every time.

Explore

Styles & brands we work with

  • Kitchen remodeling
  • Bathroom remodeling
  • Home additions & ADU
  • Roofing
  • Windows & doors
  • Driveway & pavers
  • Fence

Signs Your Plant Prefab Bathroom Remodeling Is Failing

  • Soft spots near the shower curb or toilet flange. The factory waterproofing membrane was rolled, not troweled, at the transition between the pan and the wall panel. Water has been wicking into the subfloor for months. You feel it before you see it.
  • Grout lines that crack within weeks of re-grouting. The prefab wall panels expand and contract at a different rate than the tile set over them. This is a Los Angeles-specific issue, where temperature swings between the coast and the valley put constant stress on rigid joints.
  • A vanity that’s swelling or discolored along the bottom two inches. The factory toe-kick seal fails first, then capillary action pulls water up into the MDF core. Once the core swells, the door hinges lose their bite and the whole cabinet starts to sag.
  • Mold staining along the ceiling above the shower, but only in one corner. The bathroom exhaust duct was under-specified for the module’s cubic footage at the factory. Warm, humid air condenses before it reaches the roof vent, and the moisture has nowhere to go but into the drywall.
  • A bathroom door that rubs the jamb only during winter months. The module settled after it was set on the foundation, and the framing around the door opening is carrying load it wasn’t designed for. In Los Angeles, the wet-dry cycles of our rainy seasons accelerate this in homes on expansive soil.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

In Los Angeles, a Plant Prefab bathroom remodel installs for $10,620-$33,040. The lower end covers a cosmetic refresh: new vanity, fixture swap, re-sealed shower, new flooring over the existing substrate. The upper end is a full gut-back-to-the-module-shell redo: new waterproofing membrane, relocated plumbing, tile, glass, and a custom vanity built to the module’s actual opening. What drives the price is how much of the original factory waterproofing has to be removed and re-done, plus whether the module needs shimming or re-leveling before new finishes go in. Every quote is a flat written price with a written scope and a written warranty before any work starts. Under Clause 1 of the Haven Standard, the price you’re handed is the price the job finishes at. No change proceeds without a signed change order, which is the discipline that’s kept our projects within a few percent of the agreed cost across 4,000-plus jobs.

DIY or Call Us?

You can safely check the caulk lines around your shower base and the condition of the toilet flange bolts. That tells you whether you have an active leak or just old sealant. What you should not do is pull a Plant Prefab wall panel to “take a look” behind it. Those factory panels are structural in several module designs, and removing one without understanding the load path can crack the panel, damage the waterproofing membrane, or put you in the path of a falling section. A trained professional should be the one to open the wall, diagnose the failure, and quote the repair. If you’re in Los Angeles and you’re not sure whether you have a sealant problem or a substrate problem, call (470) 298-9650 and we’ll have a background-checked technician look at it in person.

FAQs

A tile setter installing wall tile in a shower

Getting started with Rowan

Every project starts with a conversation and a written price. Here is how to take the first step.

A project lead walking the house with the homeowner during a free estimate

Free on-site estimate

A project lead walks the job with you, measures it and hands you a written, line-item price. No obligation.

Book an estimate
A crew arriving at a home with materials and tools

Find your local team

Each location is independently owned and works to the same written standard. Enter your ZIP code to reach yours.

A worker laying floor protection before work starts

Read our written promise

What we promise on every job, written down, with the terms spelled out before any work starts.

Our promise
Need Construction help nationwide? Licensed & insured · free written estimates
Call (470) 298-9650
Areas We Serve

Request a Free Estimate

Tell us what you need - Rowan Construction Group responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Send a Text
Call Now - 24/7 Dispatch