A backyard with a new horizontal privacy fence

Plant Prefab Fence Installation Nationwide

Free Estimate on SiteCalls Answered by a Live Person, 24/7Background-Checked TechniciansOur technicians have up to 19 years of experience
A new white vinyl privacy fence with a double gate
A new stained cedar privacy fence
A remodeled family room with new windows and a window seat
A standing-seam metal roof over a covered porch
A new bay window with a cushioned seat
A new concrete driveway with a paver border
A stone counter, tile backsplash and open shelf after a kitchen remodel
A remodeled hall bathroom with subway tile and a floating vanity
Every visit starts with

Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled

We have financing partners for your dream remodel*On approved credit; ask us about your options
Get your free estimate

Plant Prefab Fence Installation: The Los Angeles Owner’s Guide

Plant Prefab’s fence panels and screen walls arrive with factory-set dimensions and proprietary mounting hardware, and when the installation goes wrong or a section fails, the fix isn’t generic fencing work. In Los Angeles, we install and repair Plant Prefab-compatible fence systems for $4,130 to $10,620 depending on linear footage, post depth, and whether we’re replacing failed hardware or setting an entirely new run. The typical discovery moment is quieter than a dramatic collapse: a panel drifts out of plane, a post base shows rust bleeding onto concrete, or the gate starts dragging because the frame has relaxed from its factory spacing. Rowan Construction Group is an independent contractor, not a Plant Prefab dealer, which means we carry the fastener sets, post bases, and panel cleats that match their catalog without the markup of going back through a channel partner in Los Angeles.

Call (470) 298-9650

Which Plant Prefab Models This Applies To

Plant Prefab builds panelized screen walls and perimeter fencing that ship as pre-assembled modules, and most of what we service in Los Angeles falls into three lines: the standard cedar-and-steel privacy panels, the slatted redwood screen systems used around rooftop decks and side yards, and the all-metal perimeter panels spec’d on their multi-unit projects. The identification step matters more than owners expect. Each Plant Prefab panel carries a small aluminum tag on the bottom rail with a series code. If that tag is gone, you measure the panel’s overall width and the center-to-center spacing of the post brackets. The comon mistake is ordering by panel height alone. Two panels can stand the same 72 inches but use different post bracket spacing depending on the pour date, and that spacing changed twice in their 2018 to 2023 production runs. On the OEM vs. aftermarket question: for the visible panel hardware and gate hinges, we use Plant Prefab spec parts. For buried post bases and concrete anchors, we substitute Simpson Strong-Tie ABU bases when the factory base is discontinued, which we document in writing before the order is placed.

Explore

Styles & brands we work with

  • Kitchen remodeling
  • Bathroom remodeling
  • Home additions & ADU
  • Roofing
  • Windows & doors
  • Driveway & pavers
  • Fence

Signs Your Plant Prefab Fence Installation Is Failing

  • Panel drift at mid-span. The factory cleat system uses a nylon bushing between the post bracket and panel edge. When that bushing compresses from years of sun and wind load, the panel rotates a few degrees and the reveal goes uneven. The panel isn’t warped; the connection is worn.
  • Orange rust tracks below post bases. The original Plant Prefab mounting used a mild steel base plate that was powder-coated, not galvanized. In Los Angeles’s coastal air and irrigation overspray, that coating fails first at the weld points. The rust track tells you the post is losing cross-section where it matters.
  • Gate drag that comes and goes. If the gate clears in the morning and drags by 3 p.m., the frame is flexing with temperature. This is usually a hinge barrel that has loosened at the factory-inserted threaded stud, not a gate that needs planing.
  • Silicone peeling at panel joints. Plant Prefab weather-seals panel intersections with a specific shore-hardness silicone. Once it separates, water intrudes into the panel edge channel and the internal steel stiffener starts corroding invisibly.
  • Loose bolts that tighten and re-loosen. The factory bolts install against a nylock nut. If you can tighten one and it backs off again within weeks, the vibration thread wear means the nut’s nylon ring is dead. Replace the hardware set, not just the one bolt.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

A full Plant Prefab-compatible fence installation in Los Angeles runs $4,130 to $10,620, and most projects land between $6,000 and $8,500. The range moves with three factors: total linear footage, whether existing footings can be reused, and what the exploratory dig reveals about the original pour. A 50-foot run with clean footings and new panel hardware sits near the low end. A 120-foot run with failed post bases, re-poured footings, and a gate rebuild lands at the top. Every Rowan Construction Group quote is a flat written price with a written scope, itemized into materials, labor, and haul-off. No change proceeds without a signed change order, which is the discipline that has kept our projects within a few percent of the agreed price. The installation carries our Done Right Promise: if it is not done right, we make it right. The warranty clause is printed on the quote, not attached as a footnote.

DIY or Call Us?

An owner can safely lean a level against the post line and photograph the rust bloom at the base. That is useful evidence, and you should have it before anyone bids the repair. The line where DIY goes wrong is at the fastener torque and the footing verification. Plant Prefab panels are pre-tensioned assemblies. Over-tightening a bracket bolt introduces twist into the panel frame, and the panel will never seat flat again. Under-tightening leaves the joint loose enough to wear the bushing in six months. The footings are another blind spot: Los Angeles soil varies from sandy loam in the Valley to hardpan in the foothills, and the post base that held for ten years may be sitting on a Sonotube that was too shallow for the fence’s sail area. If you’d rather leave the torque wrench in the drawer, call (470) 298-9650 and we’ll put the price in writing before anything gets dug.

FAQs

A new wood side gate with black hardware

Getting started with Rowan

Every project starts with a conversation and a written price. Here is how to take the first step.

A project lead walking the house with the homeowner during a free estimate

Free on-site estimate

A project lead walks the job with you, measures it and hands you a written, line-item price. No obligation.

Book an estimate
A crew arriving at a home with materials and tools

Find your local team

Each location is independently owned and works to the same written standard. Enter your ZIP code to reach yours.

A worker laying floor protection before work starts

Read our written promise

What we promise on every job, written down, with the terms spelled out before any work starts.

Our promise
Need Construction help nationwide? Licensed & insured · free written estimates
Call (470) 298-9650
Areas We Serve

Request a Free Estimate

Tell us what you need - Rowan Construction Group responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Send a Text
Call Now - 24/7 Dispatch