A remodeled primary bathroom with a soaking tub and a walk-in shower

Boral Bathroom Remodeling Nationwide

Free Estimate on SiteCalls Answered by a Live Person, 24/7Background-Checked TechniciansOur technicians have up to 19 years of experience
A walk-in shower with large-format tile and a built-in niche
A remodeled hall bathroom with subway tile and a floating vanity
A remodeled hall bathroom with patterned floor tile and painted walls
A new wood side gate with black hardware
A new concrete driveway with a paver border
A stone counter, tile backsplash and open shelf after a kitchen remodel
A garage converted into a guest room and home office
New architectural shingles with a clean valley
Every visit starts with

Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled

We have financing partners for your dream remodel*On approved credit; ask us about your options
Get your free estimate

Boral Bathroom Remodeling: The Los Angeles Owner’s Guide

Boral bathroom remodeling in Los Angeles typically runs $10,620 to $33,040 fully installed, depending on whether you’re replacing a single failed component or rebuilding the entire wet area. Most Boral owners we hear from in Los Angeles discover the problem the same way: a crack that wasn’t there last month, a grout line that won’t stay sealed, or water staining the ceiling below a second-floor bath. If you’re holding a cracked Boral shower base or peeling Boral wall panel, the fix is usually measured in days, not weeks.

Call (470) 298-9650

We stock Boral-compatible trim, adhesives, and replacement panels on hand because these materials fail in predictable ways after years of California hard water and thermal cycling. Here’s what Los Angeles owners need to know before calling anyone.

Which Boral Models This Applies To

A tile setter installing wall tile in a shower

Boral’s bathroom product line splits into two families in Los Angeles homes: the Boral WPS (Wet Panel System) wall panels and the Boral Ornamental and Structural polyurethane mouldings used for trim, niches, and baseboards. They’re different polymers, different thicknesses, and they fail differently. The WPS panels are 10mm to 11.5mm solid-core composite sheets with a sealed face. The mouldings and trim pieces are a lighter polyurethane foam with a hard coat skin.

Before you order anything, check the back or edge of the failed piece for a stamped lot code and dimensions. Boral WPS panels are commonly sold in 1200mm x 2400mm sheets, but Los Angeles installs we open up often show older 900mm x 2400mm remnants from the mid-2010s. Mixing panel generations without matching the tongue profile and sealant spec is the fastest way to turn a one-panel repair into a full surround replacement. For trim, the profile number matters more than the finish; we match existing Boral crown and casing by measuring the drop and projection on site, because Boral changed two common profile dimensions in 2019 without changing the SKU format.

We are an independent Los Angeles remodeling contractor. We’re not affiliated with Boral, and we don’t pretend to be. What we do is stock the parts that match what’s already in Los Angeles bathrooms and quote the replacement with a written price before anyone starts.

Explore

Styles & brands we work with

  • Kitchen remodeling
  • Bathroom remodeling
  • Home additions & ADU
  • Roofing
  • Windows & doors
  • Driveway & pavers
  • Fence

Signs Your Boral Bathroom Remodeling Is Failing

  • Swollen or lifting edges at panel seams. Water has worked past the silicone bead and is wicking into the composite core. Boral WPS panels use a moisture-resistant core, but the edge seals fail first, especially around the shower valve and tub lip where sealant sees daily water and soap chemistry.
  • Hairline cracks radiating from screw holes or niche corners. Thermal expansion in Los Angeles, where a bathroom can swing 25 degrees overnight, puts repeated stress on the rigid panel. The crack is the symptom; the cause is usually a fastener that’s too tight or a cut corner that wasn’t stress-relieved during the original install.
  • Grout or silicone that keeps separating from the Boral surface. The hard coat on Boral trim and the face of WPS panels is smooth. Standard silicone bonds fine, but any silicone with a high acetic acid content can fail prematurely. If the last two regrouts in the same joint cracked, the panel behind it is moving.
  • Soft spots when you press on a wall panel or baseboard. The polyurethane foam core in Boral mouldings breaks down once water intrudes through a cracked coating. Press along the bottom edge of baseboards in a shower-adjacent wall; a soft Boral board means the tile or panel above it has been leaking longer than it looked like it was.
  • Discoloration or rust staining at the base of panels. In Los Angeles, that staining is often from galvanized trim nails or drywall screws that were never meant to be inside a wet area. The moisture coming through the panel is leaching iron out of the fastener and onto the surface. It’s cosmetic until it isn’t; behind the panel, that fastener is losing its thread bite.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

An open kitchen and dining area after a remodel

For a single failed Boral component, installed prices in Los Angeles run from $10,620 to $33,040 depending on scope. A one-wall panel replacement with matching trim and new waterproofing at the seams is the lower end. A full Boral shower surround rebuild with new panels, trim, niche, valve trim, and substrate repair is the upper end. Here’s the breakdown driver, because we write it this way on every quote in Los Angeles:

  • Substrate condition: If the wallboard behind the Boral panel is sound, the job is a clean uninstall, surface prep, new panel, reseal. If it’s swollen, we replace it. Usually one to two sheets of cement board and a day of labor.
  • Panel generation matching: Older Boral WPS may require re-machining the tongue or switching to a butt joint with a cover trim. That’s a line item, not a surprise.
  • Trim profile matching: If the existing Boral trim profile is discontinued, we mill or profile a near-match from the next closest Boral series. The difference is in the reveal shadow line; we show it to you before we order.
  • Faucet and valve access: Boral work around the shower valve often requires a separate plumbing stop. We pull the trim plate, not the wall, where the valve body allows.

Every quote includes the parts, the adhesive, the sealant, the substrate work, the haul-off, and a written warranty on the installation. The price is written, flat, and signed before a single panel comes off the wall. No change order, no work. That’s Clause 1 of the Haven Standard, the same document that’s governed every Rowan project.

DIY or Call Us?

You can safely check the lot code, the thickness, and the profile dimensions of a failed Boral panel or trim piece without touching a tool. That information saves us a trip and saves you a second measurement visit, and we will use it to price the job ahead of time. You can also safely remove and inspect the silicone bead at a seam to see if water is getting behind it, as long as the shower isn’t in use and the area is dry.

What we don’t advise is cutting into a Boral wall panel yourself. The panels are rigid, the cuts are unforgiving, and the waterproofing behind them is a system. A bad cut means buying a second sheet, which in Los Angeles Boral supply terms can mean a two-week lead time and a remodel that started as a Saturday project. Water damage to the subfloor or the framing from an improper patch is more expensive than the labor you saved. Measure twice, say it once, show your work. If the panel is cracked, the trim is soft, or the seam won’t seal after two attempts, call (470) 298-9650 and we’ll bring the right panel match and a written scope.

FAQs

A second-story addition that matches the existing roofline

Getting started with Rowan

Every project starts with a conversation and a written price. Here is how to take the first step.

A project lead walking the house with the homeowner during a free estimate

Free on-site estimate

A project lead walks the job with you, measures it and hands you a written, line-item price. No obligation.

Book an estimate
A crew arriving at a home with materials and tools

Find your local team

Each location is independently owned and works to the same written standard. Enter your ZIP code to reach yours.

A worker laying floor protection before work starts

Read our written promise

What we promise on every job, written down, with the terms spelled out before any work starts.

Our promise
Need Construction help nationwide? Licensed & insured · free written estimates
Call (470) 298-9650
Areas We Serve

Request a Free Estimate

Tell us what you need - Rowan Construction Group responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Send a Text
Call Now - 24/7 Dispatch