A backyard with a new horizontal privacy fence

Cover Fence Installation Nationwide

Free Estimate on SiteCalls Answered by a Live Person, 24/7Background-Checked TechniciansOur technicians have up to 19 years of experience
A new front yard fence with a matching gate
A new black aluminum pool fence with a gate
A stone counter, tile backsplash and open shelf after a kitchen remodel
A remodeled hall bathroom with subway tile and a floating vanity
A garage converted into a guest room and home office
New architectural shingles with a clean valley
A new casement window over a kitchen sink
New painted shaker cabinets with an organized deep drawer
Every visit starts with

Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled

We have financing partners for your dream remodel*On approved credit; ask us about your options
Get your free estimate

Cover Fence Installation: The Los Angeles Owner’s Guide

Cover fence installation in Los Angeles typically costs $4,130 to $10,620 for a complete system, with most residential jobs landing between $5,900 and $8,260 depending on linear footage, gate count, and whether we’re replacing an existing frame or building from scratch. We keep Cover-compatible posts, panels, and hardware on hand for the most common models, which means most Los Angeles homeowners can have the job quoted in writing and scheduled within the week. Rowan Construction Group is an independent contractor, not affiliated with Cover, but we’ve installed and repaired enough of their systems across Los Angeles County to know exactly what fails first and what it costs to make it right.

Call (470) 298-9650

The typical call starts the same way: a gate that’s dragging, a post that’s leaning after a storm, or a panel that rattles every time the wind comes through the Sepulveda Pass. Sometimes it’s structural. Sometimes it’s just hardware that gave out. Either way, the fix is specific to the Cover system you have, and we’ll identify it before we quote a dollar amount.

Which Cover Models This Applies To

A new wood side gate with black hardware

Cover’s fence systems are sold through a few major Southern California distributors, and the models that show up most often in Los Angeles backyards are the horizontal-slat and louvered-privacy lines, usually in 6-foot and 8-foot panel heights. The first thing we check when a customer calls is the post spacing. Cover’s panels are designed to sit between posts, not on top of them, so the post-to-post dimension matters more than the panel length. If your original installer set posts at anything other than Cover’s specified centers, the panels won’t seat correctly, and that’s often why they fail early.

The compatibility gotcha worth knowing: Cover’s newer powder-coated aluminum posts use a different bracket profile than their earlier steel-post systems. They look close from five feet away, but the brackets don’t interchange. If you’ve bought a home in Los Angeles with an existing Cover fence, take a photo of the bracket before you order any replacement hardware. We carry both profiles on hand. For OEM versus aftermarket, we install Cover’s own hardware when it’s available because the tolerance is tighter and the finish matches. When a panel is discontinued, we have access to aftermarket equivalents through our material suppliers, and we’ll show you the difference before we write the quote. Our sourcing relationships include brands like KraftMaid, Cambria, and Silestone for interior work, but for Cover fence installation specifically, we stick with Cover-spec materials rather than forcing a substitute.

Explore

Styles & brands we work with

  • Kitchen remodeling
  • Bathroom remodeling
  • Home additions & ADU
  • Roofing
  • Windows & doors
  • Driveway & pavers
  • Fence

Signs Your Cover Fence Installation Is Failing

  • Gate dragging or catching on the latch side. This usually means the gate post has shifted or the hinges have worn at the pin. In Los Angeles, where we get long dry seasons followed by heavy rain, the soil around unbraced posts expands and contracts enough to move a gate out of alignment within two to three years. The hinge pins on Cover gates are replaceable without pulling the whole post.
  • A post that’s leaning even slightly. A half-inch lean at the top of a 6-foot post is a warning, not a cosmetic issue. In the clay soil common through the San Fernando Valley and parts of the Westside, posts set without adequate concrete depth rotate under the wind load that comes through the passes. Cover’s aluminum posts resist corrosion, but they’ll still rotate if the footing was undersized.
  • Panels that rattle or vibrate in the wind. Cover panels sit in brackets with a small amount of designed play. When the rubber or nylon isolators wear out or fall off, the panel becomes a metal-on-metal rattle. It’s a cheap fix if caught early, and a cracked bracket if left alone.
  • Visual oxidation at the panel seams or around screw heads. Cover’s finish holds up well in Los Angeles, but coastal salt air from Malibu to San Pedro shortens the coating life by a few years. If you see white powdery oxidation around fasteners, the coating has been breached in those spots and the aluminum underneath is starting to react. We address that by replacing the fastener and touching the affected seam with a matched coating, not by spray-painting over it.
  • Sagging horizontal panels between posts. This is almost always undersized rail support or a span that was stretched beyond spec by the original installer. Cover has a maximum unsupported span per panel line, and if your fence exceeds it, the panels will dip over time. That’s not a material failure; it’s an installation error we correct by adding a mid-span post.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

A new roof with clean valleys and new flashing

A full Cover fence installation in Los Angeles runs $4,130 to $10,620 in most cases. The range is driven by three things: linear footage (most city lots are 60 to 120 feet of fence line), how many gates are involved, and whether we’re reusing the existing concrete footings or pouring new ones. A straight 60-foot run with one gate and good existing posts will land near the bottom of that range. A 120-foot run with custom gate hardware and all-new footings will land near the top.

Here’s how the numbers usually break down on a typical Los Angeles installation:

  • Materials (Cover-compatible panels, posts, brackets, hardware): 45-55% of the total
  • Labor (demo, footing work, rail installation, panel setting, gate alignment): 35-45%
  • Disposal and site cleanup: 5-10%

Every quote is a written flat price with a written scope and a written warranty before any work starts. That’s Clause 1 of The Haven Standard, and it’s been the operating rule. We don’t do verbal allowances on fence work. The number on the page is the number on the invoice unless you request a change, and no change proceeds without a signed change order. That administrative discipline is how we’ve kept 4,000-plus projects within a few percent of the agreed price.

DIY or Call Us?

There are things you can check safely. Look at your gate hinges and brackets with a flashlight. If the hardware is loose, the fix may be as simple as torquing the fasteners. You can also check post lean with a 4-foot level and check your gate’s swing path. What you shouldn’t do is remove a post from its footing, pour new concrete to correct a lean, or attempt to re-hang a full-size Cover gate yourself. A gate panel weighs more than it looks like it does, and when it shifts, it shifts with leverage. We’ve repaired more than one DIY gate repair that became a crushed finger or a bent frame. The hazard is the weight and the pinch points, not just the work itself. If the problem is structural, call us.

For anything beyond a hardware check, call (470) 298-9650. We’ll look at it, tell you what we found, and hand you a written number.

FAQs

A new multi-panel patio door opening a kitchen to the patio

Getting started with Rowan

Every project starts with a conversation and a written price. Here is how to take the first step.

A project lead walking the house with the homeowner during a free estimate

Free on-site estimate

A project lead walks the job with you, measures it and hands you a written, line-item price. No obligation.

Book an estimate
A crew arriving at a home with materials and tools

Find your local team

Each location is independently owned and works to the same written standard. Enter your ZIP code to reach yours.

A worker laying floor protection before work starts

Read our written promise

What we promise on every job, written down, with the terms spelled out before any work starts.

Our promise
Need Construction help nationwide? Licensed & insured · free written estimates
Call (470) 298-9650
Areas We Serve

Request a Free Estimate

Tell us what you need - Rowan Construction Group responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Send a Text
Call Now - 24/7 Dispatch