PGT Fence Installation Nationwide

PGT Fence Installation: The Los Angeles Owner’s Guide

A PGT fence installation in Los Angeles typically runs $4,130 to $10,620 installed, depending on linear footage, gate count, and whether we’re replacing posts or setting new ones. We stock PGT-compatible fence materials and schedule most installations within five to seven business days. Most owners call us after wind or dry rot has taken down a section, or when a gate has sagged far enough to drag on concrete. The fence line usually tells the story before you even touch it: leaning posts, split rails, hardware that’s pulled loose from wood that can’t hold a lag screw anymore.

Call (470) 298-9650

We’re an independent contractor, not a PGT dealer or affiliate. What that means for you is a straight answer on whether your existing PGT fence can be repaired section-by-section, or whether the post-and-rail system underneath has reached the point where replacing the full run makes more sense than chasing it. Either way, you get a written price before we lift a single panel.

Which PGT Models This Applies To

PGT’s fence product line in the Los Angeles market covers their aluminum and vinyl residential systems, most commonly the PGT aluminum panel line and the PGT vinyl privacy series. The compatibility gotcha we see most on service calls is width: older PGT aluminum panels were produced in 6-foot sections, while newer inventory ships in 8-foot spans. If you’re replacing one damaged 6-foot panel on an older run, you may need to fabricate a color-matched panel rather than expecting an off-the-shelf match at a supply house. It’s one of the reasons we keep both lengths in stock and have a local fabricator we trust for custom cuts.

To identify what you have, check the bottom rail of an existing panel or the post cap for a PGT stamp or sticker. If that’s faded away, measure the distance between post centers. The panels are designed to fit between posts, not over them, so getting that number right is the difference between a clean install and a fence line that oscillates in the wind. We also verify post spacing against PGT’s published racking tolerance for slope. Los Angeles hillside lots with grade changes need stepped or racked installations, and not every aluminum panel line is rated for steep racking.

Signs Your PGT Fence Installation Is Failing

• Sagging gate with a visible gap at the latch side. The hinge posts have usually shifted or rotted at the base. In Los Angeles, we see this most after winter rain hits compacted clay soil around the post footing.
• Panels rattling in wind or moving when pushed. The bottom rail screws or brackets have backed out or stripped. Aluminum expands and contracts with temperature swings; over years, that cycling loosens fasteners.
• Posts leaning at the corners or gate positions. The post wasn’t set deep enough or the concrete footer cracked. Corner posts carry the tension load of the entire run; when they go, the rest follows within a season.
• White oxidation or blistering on aluminum panels. This means the factory powder coat or anodized layer has failed, and salt or contaminant exposure from coastal air or irrigation overspray is corroding the base metal.
• Bottom rail bowed or touching the ground. Frost heave or soil movement is pushing up on the post, and the panel is absorbing the flex. In Los Angeles the culprit is usually swelling from irrigation runoff, not frost.

Before

After

Replacement Cost & What’s Included

For a full PGT fence installation in Los Angeles, plan on $4,130 to $10,620. At the low end, you’re looking at a straightforward 60 to 80 linear feet of vinyl or aluminum panel on level ground with one walk gate, no demo of concrete footers. At the high end, you’re dealing with hillside racking, multiple gates, old concrete removal, and possibly stucco wall returns where the fence ties into the house. Every quote we write in Los Angeles breaks out the material cost, the labor cost, and the disposal fee as separate line items. That’s the only way you can compare it to another bid line by line, and it’s how we’ve kept 4,000-plus jobs within a few percent of the number the customer agreed to. The installation work carries our 365-Day Done Right Promise: if it’s not right, we make it right.

DIY or Call Us?

You can safely check a few things yourself: how many posts are leaning, whether the gate still opens without dragging, and whether panels are loose at the brackets. What often goes wrong on DIY PGT fence work is post setting. Getting the depth right, using the correct concrete mix for Los Angeles soil conditions, and keeping the post plumb while the footing cures takes tools most homeowners rent once and never want to rent again. If a post pulls free and a panel falls on a neighbor’s car or a pedestrian, that’s a liability you carry alone. We carry the insurance, the tools, and a crew that sets posts every working week. Call (470) 298-9650 if you want us to come look at the fence line and give you a written price.

FAQs