A remodeled primary bathroom with a soaking tub and a walk-in shower

Sakrete Bathroom Remodeling Nationwide

Free Estimate on SiteCalls Answered by a Live Person, 24/7Background-Checked TechniciansOur technicians have up to 19 years of experience
A remodeled primary bathroom with a soaking tub and walk-in shower
A freestanding soaking tub in a remodeled primary bathroom
A walk-in shower with large-format tile and a built-in niche
A new paver pool deck
An open kitchen and dining area after a remodel
A second-story addition that matches the existing roofline
A newly finished roof with a ridge vent and step flashing
A new front entry door with glass sidelights
Every visit starts with

Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled

We have financing partners for your dream remodel*On approved credit; ask us about your options
Get your free estimate

Sakrete Bathroom Remodeling: The Los Angeles Owner’s Guide

If you’re holding a Sakrete product and planning a bathroom remodel in Los Angeles, the installed cost typically runs $10,620-$33,040 depending on scope, and we can usually start within two weeks of the written quote. Sakrete makes concrete mixes, levelers, patching compounds, and waterproofing underlayments that show up constantly in LA bathroom work, especially where older homes have settled slabs or failed mortar beds. Most owners don’t discover a Sakrete-related problem until tile cracks, a pan liner leaks, or demo reveals a substrate that was never properly sloped or sealed. That’s the moment this guide is for.

Call (470) 298-9650

We’re an independent Los Angeles contractor, not affiliated with Sakrete. What we do is work with their products daily, know their spec sheets cold, and know which failure patterns repeat across the city’s housing stock: 1920s bungalows in Echo Park, post-war ranch homes in the Valley, 1990s condo conversions in Mid-Wilshire. Same products, different substrate problems underneath. The prep underneath it usually is.

Which Sakrete Products We Work With in Bathroom Remodeling

A tile setter installing wall tile in a shower

Sakrete’s line splits into concrete and mortar products, and each has a specific place in a Los Angeles bathroom. The ones we specify and install most often include:

  • Sakrete Sand Mix (SKU 110019) – for shower pan pre-slope and final mortar bed. This is the workhorse under every tile shower floor. It mixes to a 5:1 sand-to-cement ratio and should be packed, sloped 1/4 inch per foot, and cured before any waterproofing goes down.
  • Sakrete Top’n Bond Concrete Patcher – for repairing spalled or chipped slab edges where a tub or shower base sits. Los Angeles homes on post-tension slabs often have hairline cracks at the wet wall; this patches them without overlay.
  • Sakrete Floor Leveler – for correcting slab dips before setting large-format tile. Anything beyond 1/8 inch over 10 feet will telegraph through tile, and we measure that with a 10-foot straightedge before quoting.
  • Sakrete Waterproofing and Anti-Fracture Membrane – for wet areas where a roll-on membrane is called for instead of sheet membrane. This is a trowel or roller-applied system that must go on in two coats at right angles, and the dry film thickness matters more than most installers admit.
  • Sakrete Fast-Setting Concrete Mix – for re-setting tub bases and filling old soap dish recesses in lath-and-plaster walls. Reaches 400 psi in about 40 minutes, so the work window in a hot LA summer is short.

The compatibility gotcha with Sakrete products is simple: these are cementitious materials, and cementitious materials shrink. If you’re matching a patch to a 60-year-old mortar bed, the new material will cure harder and drier than the surrounding material. That differential is what causes the patch to debond at the edges within a year or two. In LA’s dry climate, where indoor relative humidity can sit at 30 percent in September, that cure happens fast and the bond line fails faster unless you damp-cure or use a bonding agent. We keep the spec sheets on hand because the difference between a successful patch and a callback is often 48 hours of cure time and one skipped step.

Explore

Styles & brands we work with

  • Kitchen remodeling
  • Bathroom remodeling
  • Home additions & ADU
  • Roofing
  • Windows & doors
  • Driveway & pavers
  • Fence

Signs Your Sakrete Bathroom Substrate Is Failing

Here’s what we see when existing Sakrete work has gone wrong in Los Angeles bathrooms, and what each symptom actually means:

  • Hollow-sounding tile or drummy tile. Tap the tile with a wooden handle. A hollow sound means the mortar bed has debonded from the substrate. This is usually a prep failure: the Sakrete material was mixed too dry, the concrete below was too smooth, or dust was never removed. The tile may hold for years, but it will eventually crack under foot traffic.
  • Cracks running in a grid pattern across the floor. This is reflective cracking from a non-structural slab crack below. If the anti-fracture membrane was skipped or applied too thin, the tile mirrors the slab. In Los Angeles, slab movement from minor seismic settling is continuous, not a one-time event.
  • Water staining on the ceiling below a second-floor bathroom. The shower pan failed, and the Sakrete mortar bed has been holding water. A properly built pan has a sloped mortar bed over a waterproof liner. When the liner gets punctured or the weep holes clog, the mortar becomes a sponge that drains through the ceiling.
  • Crumbling grout or grout that turns to powder. This points to moisture wicking up through the substrate, or efflorescence from the cement dissolving salts. Sacramento? Different story. In Los Angeles, the hard water chemistry and the building’s age both matter. Old mortar beds hold minerals that migrate upward through capillary action.
  • Tub or shower base that rocks or flexes. The original setting material under the tub has broken down. This is common in homes where the slab has settled unevenly. The fix is lifting the tub, re-setting it in new Sakrete mortar, and letting it cure under weight.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

New architectural shingles with a clean valley

A full Sakrete-related bathroom remodel in Los Angeles runs $10,620-$33,040. Here’s what drives that range, and what you’re paying for:

Scope Typical Los Angeles Installed Cost
Shower pan rebuild (demo, pre-slope, Sakrete pan, membrane, tile) $5,310-$14,160
Floor leveling + large-format tile reset $2,360-$7,670
Tub re-set in fresh mortar, including plumbing connections $4,130-$11,800
Full bathroom remodel with vanity, fixtures, tile, and substrate repair $10,620-$33,040

The range comes down to three things: substrate condition once demo opens the floor, tile size and material, and what’s hidden behind the walls. We write the quote after opening up enough of the floor to see the slab condition. Clause 1 of the Haven Standard means there’s a written price on the table before any work starts, and if we find something unexpected mid-job, no change proceeds until you sign a change order. The workmanship warranty is in writing on every quote, and the Done Right Promise backs it: if it’s not done right, we make it right.

DIY or Call Us?

You can check the drummy tile yourself. Tap it. Note the cracks. Photograph the water stains. That documentation helps us price the job accurately on the first visit. What you shouldn’t do is attempt any part of the correction yourself. Cementitious work is chemically aggressive before it cures, heavy to handle, and unforgiving of timing mistakes. A poorly sloped shower pan fails silently for months before showing damage. A mortar bed that sets too fast in a hot Valley summer creates a weak layer that cracks under its own weight. We’ve rebuilt more DIY-er pans in Los Angeles than we can count. If you’re ready for a real look at the underlying substrate, call (470) 298-9650 for a free estimate. We’ll bring a straightedge, a moisture meter, and a written number.

FAQs

A new casement window over a kitchen sink

Getting started with Rowan

Every project starts with a conversation and a written price. Here is how to take the first step.

A project lead walking the house with the homeowner during a free estimate

Free on-site estimate

A project lead walks the job with you, measures it and hands you a written, line-item price. No obligation.

Book an estimate
A crew arriving at a home with materials and tools

Find your local team

Each location is independently owned and works to the same written standard. Enter your ZIP code to reach yours.

A worker laying floor protection before work starts

Read our written promise

What we promise on every job, written down, with the terms spelled out before any work starts.

Our promise
Need Construction help nationwide? Licensed & insured · free written estimates
Call (470) 298-9650
Areas We Serve

Request a Free Estimate

Tell us what you need - Rowan Construction Group responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Send a Text
Call Now - 24/7 Dispatch